STRUCTURAL AND REINFORCEMENT DETAILING OF A SINGLE STOREY RESIDENTIAL BUILDING
102 Users found this project useful

STRUCTURAL AND REINFORCEMENT DETAILING OF A SINGLE STOREY RESIDENTIAL BUILDING

 

PREFACE

            This is presentation of information on the detailing of structural members in Buildings. Structural detailing is a branch of structural work that transposes the ideal or works of a Structural Engineer in working drawings for easy utilization in the building construction works. Working drawing are produced by an architect and a structural Engineer for easy use by a contractors.

            The processes of detailing put n place was in conjunction with the recommendation of the concrete society and the Institute of Structural Engineers. In building construction, a good interaction and relationship between the architects Structural Engineers, Quantity Surveyors and Contractors are required. The methods, scales, symbols and notations must be stonverdized and understood by all parties involves in a project to immunize risks and communication hindrance.

            A structure in broken down into identifiable elements for detailing work like beams, columns, slabs etc which enables the different detailing aspects to be fully addressed and understood. 

STRUCTURAL SYMBOLS

            The abbreviation recommended for structural detailing works are as follows:-

            R.C                  =          Reinforced Concrete

            Nog                 =          Drawing

            Hor                  =          Horizontal

            Vest     =          Vertical

            Dia                  =          Diameter

            Fdn                  =          Foundation

            Cone                =          Concrete

            Col                  =          Column

Types of Reinforcement

            R         =          Mild steel bars

            Y         =          High yield bars

Comments relating to Reinforcements

L          =          Centre line

B         =          Bottom

T          =          Top

C/c       =          Centre to centre

TABLE OF CONTENTS 

 CHAPTER ONE: INTRODUCTION

CHAPTER TWO: DETAILING PROCESSES

CHAPTER THREE: DESIGN, CONDITION, AND SUMMARY

CHAPTER FOUR: REINFORCED CONCRETE 

CHAPTER FIVE: ENGINEERS DESIGN SPECIFICATIONS

CHAPTER SIX: DETAILING OF THE ELEMENTS

A         FOUNDATION

B         COLUMNS

C         BEAMS

D         SLAB

E STAIRCASE

BIBLIOGRAPHY

 

CHAPTER ONE

INTRODUCTION

BACKGROUND OF THE STUDY

 Before a designer can relate his requirements clearly in construction industry, a drawing is to be prepared, this is because the drawing serve as a general means of communication. Therefore the drawing is adopted mostly, than other means of communication in the Engineering Sectors.

A structural Engineer mostly engages himself in designs on construction of structure, like roads, bridges, railway, dams, building, runway and other public works.

 The structural engineer makes initial design, which are usually free – hand sketches of the work. These sketches are used to make clear and neat working drawing, which will be used by the builder of contractor after approval for construction by the authorities involved.

The contributions of a detailer in highly significant to the construction process, for a well detailed drawing is a good medium of reducing the risks of building collapses and to avoid delays arising from doubts and too frequent classifications.

Floor plan                                                        1:75; 1:50

Foundation plan                                            1:75; 1:50

Elevation                                                         1:75; 1:50

Construction details                            1:20; 1:10

Cabinet details                                                1:50; 1:25

Wall sections                                       1:20; 1:10

Details of connection, lings    1:5; 1:2

Etc.

PLANS

Plans shall be drawn as transverse section through all structural members immediately above portion of structure under consideration.

ELEVATIONS

 Elevations shall be drawn as a vertical section immediately adjacent to the element under consideration. Structural members cut by the section shall be shown in full lines and member behind the section in broken lines.

SECTIONS

Sections shall show only material out by the section plan. The dimension of sections shall be of the left for beams and downward for column. The section shall be drawn as close as possible to the plan or elevation to which it refers and should be described by letters, readable from bottom of the drawing. Section through concrete on drawings may be show as highly shade areas.

GRID LINES

Grid lines provide a reference system for beams and column. It is convenient from top to left corner of the drawing using letters for one direction and numbers for the other.

Gridlines do not necessarily have to be straight or at right angles to each other or actually pass through beams or columns but should be sufficiently class for the reference to be obvious.

Equipment

Pencils and drawing pans

Drawing boards and tee square

Drawing sheet / paper

Set square

Tracing sheet

Lettering grid

Templates

Protractor

Drafting table

GET THE COMPLETE PROJECT

Peace From Unilag

I cried not knowing how to go about my project but the day i searched online and saw iprojectmaster, i called and got my full project in less than 15minutes, i was shocked!


Oluchi From Michael Opara University

If you are a student and you have not used iprojectmaster materials, you are missing big time! iprojectmaster is the BEST


Uduak From Uniuyo

iProjectMaster is the best project site for students. Their works are unique and free of plagiarism!


Musa From Ahmadu Bello University

Thank you iprojectmaster for saving my life, please keep it up and may God continue to bless you people.


Samuel From Ajayi Crowther University

You guys just made life easier for students. Thanks alot iprojectmaster.com


Merry From BSU

I am now a graduate because of iprojectmaster.com, God Bless you guys for me.