DOWNLOAD THE COMPLETE PROJECT

2604 Users found this project useful

DESIGN AND FABRICATION OF MODERN LOCKABLE BOOKSHELF

CHAPTER ONE 

1.1  INRODUCTION

A metallic lockable bookshelf is a rectangular piece metal device and fabricated for the main purpose of artery keeping of book, files audio and vides cassette in homes, offices and libraries etc. as well as retrieval and consultation when needed. On starting of this project a lot of consideration was done based on the workability of such project, the consideration of material available as well as they choice of the advantages of the material later stetted including research on the regimen properties of the material with at most carefulness if such material chosed is combustible, environmental finally or Harvard an resistance to insects attack like metals instead f wood. Strenuous become the consideration to make the project quite affordable, this in the area of cost of production which was over comer by adopting certain amendment with the need to achieving the shelf in such a way that it become a modern lockable bookshelf which can contain quite number of books and files. It was felted with rollers stands and stoppers for stability at any kept point and easy movement and solidity welded

1.2  DESCRIPTION LOCKABLE BOOKSHELF OF THE MODERN

The modern lockable bookshelf.

Was constructed using 20mm square pipe and gauge 15mm mild steel street/plate and comprises of the totting parts /components:

i.            Base

ii.            Side

iii.            Partitions or rocks.

iv.            Roller Stands

v.            The doors

vi.            Locks

vii.            Stopper

viii.            Book

MATERAL SELECTION

In everyday work, an engineer comes across certain material like steel grides. Angle non circular bars, wrought iron, Aluminum etc. which are to be used  in fabrication of projects. While selecting a suite as ability t resist stress (tensile stress and comprehensive stress), strewn, elastic limit etc under the external force. It has been observed that under the influence these forces, the material is first deterred and made an the forces and their sheet along with some suitable precutting measures to determine the strength of material and to have a better quality product. As the case may be, this knowledge is very essential for an engineer to enable him design and fabricate his project.

1.2.1    THE BASE / BASE TOP.

The base is made up of that sheet properly reinforced with 20mm square pope at all four rectangular sides of the rollers and stopper. The quality of this enforcement was bultress by good welding job and tilling eared out. He width is 70mm. The base top has no roller tiller (. Fig 1B)

1.2.2. THE SIDES

The side as shown in fig is of a mild steel plate sheet of gauge 20, having a height and width dimensions of 10mm and 370mm it was properly reinforced with a for (20mm) square pope after framing and bending of the sheet at an angle of go which serve a propose of safety handling. The welding of this side was done with guage 12 mild steed. Doctored to show more stability or solidity knowing fully well that it will help in carrying the locks / partitions.(fig 1 A)

 1.2.3   THE BACK

The back of the modern lockable bookshelf was of gauge 15mm mild steel which was formed as was bent at an angle 90o with the correct exact marking out of 910mm as length, 770mm as width. The essential of the back being to serve a cover and support to carry the locks, based on this the back was reinforced and welded in place/position see fig ld.

1.2.4    PARTITIONS OR LOCKS

The locks (partition) used were of metal sheet of the gauge 15mm. Being the place where the books will be kept the folding of by an angle 900 was done and welded in the square pope with at most aim of smoothness and easy handing of the book in place. The shape is rectangular length 765mm, 300mm width positioned at a distance of 300mm from one lock to another. The lock was welded inside the shelf properly in other to gain and maintain rigidity.

1.2.5  ROLLERS

The roller fitted to the modern lockable shelf is oracular in shape. The important of the rollers is to enable easy movement and it carries the shelf and also its entire load based in this the rollers was fitted in the shelf by welding to enable strong grip and avoid slip paring of the roller.

1.2.6.   THE DOOR

The door of the shelf is of 370mm width and 850mm length made from metal sheets into shape by an angle of 900 and the welding reinforcement and rigidity of the door by the used of square pope the door was in two joined to the shelf by 2 inches hinges to the shelf (i.e. 25mm inches).

  DOWNLOAD THE COMPLETE PROJECT